White powder tile adhesive – TN1000

A single-component powder adhesive in two colors: white and gray, containing nanostructured additives for installing tiles and ceramics. This adhesive provides excellent adhesion and high resistance to temperature changes, making it a suitable option for installing tiles in a variety of spaces

Porcelain powder tile adhesive

Porcelain powder tile adhesive is produced as a single component and in two colors: white and gray. This adhesive contains mineral powders, polymer additives, thickeners, nanostructure additives, cement and other additives. After mixing with water, it is ready to use

Application cases

This product is suitable for installing medium-sized ceramic and porcelain tiles and natural stone on a variety of absorbent and non-absorbent horizontal and vertical surfaces inside and outside the building

Advantages of using porcelain powder tile adhesive

  • Maintains strength against humidity and immersion in water
  • Speed ​​and ease of implementation
  • Very high strength and adhesion strength
  • Easy to mix with water
  • Powdered tile adhesive is improved using nanotechnology
  • Has a complete formulation and no need to mix with other additives

Physical and chemical properties of porcelain powder tile adhesive

  • Physical state: Powder
  • Application mode: paste
  • Color: White and gray
  • Powder density: 31.45 g/cm
  • Ion Chlorine: None
  • Adhesion strength: more than 20.5 N/mm
  • Standard: In accordance with Iranian Standard 12492, published in 2019 – Type C1
  • Type: C1
  • Usage time: one hour
  • Open time: at least twenty minutes

How to use porcelain powder tile adhesive

First, ensure the quality of the surface under the work. The surface under the work must be smooth, sound, of appropriate strength and free of any grease, dust and loose particles. If tiling is done on old tiles, remove the glaze of the tiles under the work with an axe

To make the tile adhesive, add up to 3 liters of water for every ten kilograms of powdered tile adhesive and mix the adhesive using an electric mixer. Slowly add the water to the powder and continue mixing for three minutes until a soft and uniform paste is obtained

Leave the resulting paste for ten minutes and, if necessary, adjust its consistency by adding water. The consistency of the adhesive should be such that after installing the tile, the tile does not immediately separate and the back of the tile remains soaked with adhesive. If the adhesive is hard, tiles, ceramics and stone will not stick to it

After preparing the adhesive, thoroughly coat the back of the tile and the surface under the work with the adhesive using a notched trowel and press the tile onto it. To improve adhesion, gently move the tile into place while pressing

The tiles should be placed on the glued surface within a maximum of twenty minutes. The prepared adhesive should be used within one hour. If the adhesive dries before use, it can no longer be used and should not be diluted with water

The setting time for tiles installed on highly absorbent surfaces is twenty-four hours, and for surfaces with low absorption or larger tiles, more time is required

Packaging

Bidak’s TN1000 tile adhesive is available in 20 kg waterproof packages

Consumption rate

Depending on the roughness of the surface under the work and the condition of the grooves on the back of the tile, about 3 to 6 kilograms of powder tile adhesive are required to cover one square meter

Conditions and duration of storage
  • Store out of reach of children, direct sunlight and moisture, at a temperature of plus five to plus thirty-five degrees Celsius, and in an indoor environment
  • The adhesive will remain usable for up to eighteen months if stored under the stated conditions and in the original sealed packaging

Please contact the company’s consultants for technical advice


Fatal error: Uncaught wfWAFStorageFileException: Unable to verify temporary file contents for atomic writing. in /home3/bidakcoc/public_html/wp-content/plugins/wordfence/vendor/wordfence/wf-waf/src/lib/storage/file.php:51 Stack trace: #0 /home3/bidakcoc/public_html/wp-content/plugins/wordfence/vendor/wordfence/wf-waf/src/lib/storage/file.php(658): wfWAFStorageFile::atomicFilePutContents('/home3/bidakcoc...', '<?php exit('Acc...') #1 [internal function]: wfWAFStorageFile->saveConfig('livewaf') #2 {main} thrown in /home3/bidakcoc/public_html/wp-content/plugins/wordfence/vendor/wordfence/wf-waf/src/lib/storage/file.php on line 51